Industry news - How to Avoid Folder-Gluer Rejects

Industry News - How To Avoid Folder-Gluer Rejects

Folding and gluing machines create hundreds upon hundreds of packaging every hour they operate. And it’s in the best interest of manufacturers to ensure that as few of these as possible contain defects.

 

It is critical to avoid creating rejects to avoid extra costs and wasted time. Here are the best practices of folding and gluing processes to avoid defects in the packaging you manufacture.

 

Creating an Accurate Design: It is important to consider the folding and gluing process during the design stage and other considerations regarding design. This is because the process is three-dimensional. Any mistakes in the design can cause defects to occur more often during the manufacturing process.

Ensure that all measurements in the design are accurate. This becomes more important the more complicated the shape of the packaging is.

The score lines are another important part of the design. These are the lines along which the paper or carton will be folded. These must be as accurately placed as possible to avoid an uneven shape.

 

Coating before Running Stock Through the Folder-Gluer: Coating helps prevent scuff and protects the print during gluing and folding. You can apply either a cured UV or aqueous coating inline or offline. Even once coated, you should avoid having the stock get in contact with guides, bars, and another static tooling.

If you run the stock through the folder-gluer, do so after the ink has dried completely. Wet ink will easily scuff and offset from tracking on the machine.

 

Avoid Coating Glue Flaps: Coating protects the stock. However, it can also prevent the glue from properly penetrating the paper stock and creating a proper bond. This is why it’s important to avoid any type of coating on the glue flaps.

Some technologies, like plasma treatment, allow operators to treat the coating so the glue will penetrate. However, how well this works depends on the coating being applied properly. This makes it less efficient than avoiding coating the glue flaps, as one defect in the coating means another defect in the gluing.

 

Preparing Metallic Surfaces for Gluing: Without proper treatment, a stock that includes hot foil, cold foil, or a metallic board will not glue properly. During the die-cutting process, perforations can be added to the gluing area. This allows the glue to penetrate the metallic surface.

You can also use a combination of hot melt and cold glue. The hot melt can help the cold glue by giving it dots which it can use to bond the carton together.

 

Use Quality Paper Stock and Carton Board: The folding and gluing process is affected by the quality of the paper stock or carton board. The higher the quality, the smoother it runs through the folding-gluing process.

However, this also costs more. Manufacturers have to balance the cost and quality to produce the least amount of rejected packaging while not paying too much for a high-quality stock. Larger runs might need a better-quality stock, so consider this as well.

 

The Right Scoring and Folding Process for the Stock: There are many packaging materials like paperboard and corrugated cardboard. The best process differs depending on what is being used. Heavier boards should be scored in the same direction as the paper grain. This results in it being folded better. The lighter stock should be scored from the opposite side.

The best way to determine the best process for what you’re using is to ask your provider simply. Typically, die makers have comprehensive charts that tell you which way of scoring will result in the best folds for the stock you’re using.

 

New, Clean Belts: Scuffing can also be caused by the belts, particularly with the feeder section, where they accelerate to speeds greater than 22 mph within seconds. This can create a burn-out effect on the print. Using newer, cleaner belts and allowing the paper stock or carton to come into contact with as much of the surface of the belt as possible will reduce the effect.

 


 

Thank you for choosing Royo Machinery!

Royo Machinery is your perfect ally when purchasing machinery, as our team will guide and support buyers every step of the way: from pre-purchase inspections, dismantling and removal, cleaning and rebuilding to transportation, installation, after-sales service, and professional consultation. We offer the possibility to automate the production process, allowing companies to be more competitive. The automation of the finishing procedures reduces the cost of labor, increases efficiency, and improves the quality of the final product. In the end, this investment translates into noticeable profits.


 
 
हमारे बारे में

रोयो मशीनरी नए और पुराने प्रिंटिंग, फिनिशिंग और कार्टन कंवर्टिंग उपकरणों के दुनिया के सबसे अनुभवी आपूर्तिकर्ताओं में से एक है। हमने पिछले 76 वर्षों में किसी भी अन्य डीलर की तुलना में कैरिबियन और लैटिन अमेरिका में नए और पुराने ऑफ़सेट प्रिंटिंग और फिनिशिंग उपकरण बेचे हैं। इस क्षेत्र में हमारे विशेष संबंध और समझ हमारी कंपनी को प्रतिस्पर्धियों पर प्रतिस्पर्धात्मक बढ़त देती है।

रोयो परिवार को दुनिया में कहीं भी नए और पुराने प्रिंटिंग, फिनिशिंग और कंवर्टिंग को खरीदने और बेचने की प्रक्रिया को प्रबंधित करने के लिए आवश्यक लॉजिस्टिक्स और इंजीनियरिंग की मदद करने के लिए सबसे ज्यादा अनुभव है। हम अन्य सेवाएं जैसे पूर्व खरीद निरीक्षण, मशीन को खोलने और हटाना, पार्ट्स, सफाई और पेंटिंग, पुनर्निर्माण और रेट्रोफिटिंग, परिवहन, स्थापना और प्रदर्शन, बिक्री के बाद सेवा और वारंटी, मूल्यांकन और पेशेवर परामर्श उपलब्ध करवाते है।

1948 से उद्योग में होने के कारण हमने एक सक्षम वैश्विक नेटवर्क बनाया है जो आपके लिए नए और पुराने प्रिंटिंग, फिनिशिंग और कार्टन कन्वर्जिंग उपकरणों को अधिक प्रतिस्पर्धी कीमतों पर ढूढ़ने के लिए समर्पित है। हमें आपके लिए ऑफसेट प्रेस, पेपर कटर, फोल्डर, डाई कटर, बॉक्स फोल्डर ग्लूअर, यूवी कोटर, रोल शेटर या लामिनेटर को उपलब्ध करने का अवसर दे ।

WohlenbergKomariManrolandPolarRyobiMBOGOSS
BobstMitsubishiMuller MartiniKolbusWifagKBA